Les routeurs Cisco et IOS. Configuration de la route par défaut. En mode configuration ip route adrIPReseau masque adrIPGateway route statique. Le pare-feu VPN sans fil N Cisco RVW comprend: la prise en charge du routage statique, versions RIP (Routing Information Protocol) 1 et 2 et du routage. CONFIGURATIONS LINUX Vérifiez que ROUTEUR CISCO IOS: a , ROUTEUR QUAGGA A interface.

Author: Ditilar Kagagrel
Country: Albania
Language: English (Spanish)
Genre: Education
Published (Last): 22 March 2008
Pages: 117
PDF File Size: 6.39 Mb
ePub File Size: 20.86 Mb
ISBN: 290-2-93510-688-9
Downloads: 77990
Price: Free* [*Free Regsitration Required]
Uploader: Fetaxe

Exercice de routage statique IPv4 et IPv6 en Cisco IOS

Powerline Adapter Transforms electrical wiring to carry ciscp network signal. Input destination network, subnet mask, default gateway, select status and save it. Is this faq useful?

Static routing can also be used in stub networksor to provide a cisxo of last resort. Your feedback helps improve this site. In order to solving the issue, you have to set up a static route on router2. Switches Boosts your business network with premium performance. Static Route Overview Static Route Overview If you decide that you want specific Layer 3 traffic to take a certain route without participating in IP routing protocols, you Please turn it on for the best experience.

Sign Up Follow Configuratoin www. The administrative distance is a measure of trustworthiness where lower numbers are considered to be more trustworthy than higher numbers.

Configure a Static Route

The simple syntax of static route: Therefore, if you want PC to visit servers in intranet, you have to set up a static route on router2 helps your packet route to router1. How to configure Static Routing on wireless routers? TP-Link takes your privacy seriously.


Suppose that your company has 2 branches roytage in New York and Chicago. Static routing, if used without dynamic routing, has the following advantages: The commands to add a static route are as follows: Static route is often used when your network has only a few routers or there is only one route from a source to a destination.

Reverse-Path Forwarding PIM uses reverse-path forwarding RPF to prevent routing confihuration and to build a shortest-path tree from the receiver back to the multicast source.

Notice that static route works one-way. The following is typed foutage a terminal: Now we consider a real-world example of static routing. This page was last edited on 26 Decemberat If you configure clsco static route pointing to an exiting interface for example: Choose this option if you want the route used only for unicast traffic. Because there is no route to server1 and server2 on route table of router2, thus the request will be thrown away.

Well, 1 is the administrative distance AD and 0 is the metric of that static route. Administrative distance is the value from 0 to IP subnet mask for this address is Static routing can have some potential disadvantages: In fact, R0 can successfully ping R1 right after adding the static route to R0.


Next VR —Select this option and then select a virtual router if you want to route internally to a different virtual router on the firewall. OSPF has an administrative distance of Both —Install the route in the unicast stztique multicast route tables available for IPv4 routes only.

Configure Static Route – GNS3 Lab

With dynamic routes, routers can communicate with each other to exchange routing information. Static route and Dynamic route Static route tells the device exactly where to send traffic, no matter what.

Static routes can also be added by specifying the exit interface rather than the “next hop” IP address of the router. Unicast —Install the route in the unicast route table.

Multicast —Install the route in the multicast route table available for IPv4 confiugration only.

Enterprise-level Cisco routers are configurable using the Cisco IOS command line, rather than a web management interface. So there are 2 networks statjque are directly connected to R0: Static routes have an administrative distance of 1 so in the outputs above you will see the administrative distance of both static routes are 1.

And the page of Static Routing would appear on the screen: This Article Applies to: R1 config ip route

Author: admin